What are your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently available, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also embeded in the new one. Ensure you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to think about utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This article will assist you set up a new tub in your washroom if you have currently bought a new tub and don't need to change the setup of your previous supply of water pipes.
Your tools and product checklist must make up the following:
Preparing for the Installment
To start with, the supporting structure provided with the bathroom should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited accessibility that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of the two wooden boards under its feet, place the bath tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the water supply and inspect all joints and brand-new pipework for leakages and also tighten them if necessary. Load the bathtub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, repair the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub must wait until the bathtub has been made use of at least once as this will certainly resolve it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washers are in area in between the tap and the sink. Safeguard the tap in place with the producer provided backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be connected to the faucet ends first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, creating the water to permeate the wall in between the bathroom and also the tiling, bring about complications with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub Yourself? Write a remark further down. We will be delighted to hear your thoughts about this article. Hoping to see you back again before long. Sharing is good. Who knows, you may very well be doing someone a favor. I am grateful for your time. Don't hesitate to stop by our blog back soon.
Top plumbers, one call.